Stainless steel made, with 12 slots, they are supplied with two collecting pans. Opening: 1/2" (12.7mm)Weight:1.2kg
The liquid limit device is used to determine the moisture content at which clay soils pass from a plastic to a liquid state. This model is hand operated with left side crank and hard rubber base. Weight: 3 Kg approx
Used for the precise division into two representative portions of materials such as: aggregates, sand, gravel and similar. Painted steel made, it is supplied with two collecting pans.
Used for the precise division into two representative portions of materials such as: aggregates, sand, gravel and similar. Painted steel made, it is supplied with two collecting pans.
Used for the precise division into two representative portions of materials such as: aggregates, sand, gravel and similar. Painted steel made, it is supplied with two collecting pans. Opening:1 1-2” - 45 mm Weight: 12 kg
Available in the following models: V112: Ø100mm x 60 mm height V112-01: Ø 125mm x 65 mm height V112-02: Ø 150mm x 76 mm height V112-03: Ø 180mm x 92 mm height V112-04: Ø 200mm x 100 mm height
Mortar and pestle, porcelain, diameter 125 mm
Pipette method The complete set comprises: S144 Andreasen pipette, 25 ml capacity, for an accurate extraction of the quantities of soil in suspension for analysis. S144-01 Pipette stand to accurately raise and lower the pipette with no transmission of vibration to not disturb the sample suspension....
Mould to produce a specimen of 140 mm.long x 12.5 mm radius. This test covers the determination of linear shrinkage of soils and indicates the plastic properties of soils with a low clay content. Weight:500 g
This liquid limit device is motor operated at 120 drops/min speed, with a hard rubber base.Power supply: 110V 1ph 60HzWeight: 3.5 Kg
Used for the precise division into two representative portions of materials such as: aggregates, sand, gravel and similar. Painted steel made, it is supplied with two collecting pans.
Sample splitter designed for the reduction of test samples which are too large in volume to be conveniently handled. It handles any material from sand sizes up to dia. 108 mm. Each chute bar is 12 mm wide so that openings of 12-24-36-48-60-72-84-96-108 mm are possible. Complete with two collecting p...
Used for the precise division into two representative portions of materials such as: aggregates, sand, gravel and similar. Painted steel made, they are supplied with two collecting pans. Multiple models available: A064: slot width 3-4", 19 mm; max. size sample 13 mm; slot number 12, weight 11 ...
Used to determine the maximum moisture content at which the soil does not shrink after drying the sample. Complete with carrying case. The set comprises: V122-04 Shrinkage dish, Ø 45x12.7 mm (2 pieces) V122-03 Crystallizing dish, Ø 57x32 mm S175-03 Shrinkage prong plate, made from ple...
Used to determine the specific gravity of soils, it rotates two gas jars at approx. 50 rpm to satisfy BS Standard.The shaker is equipped with an original friction device conforming the unit to CE Safety Directive.Supplied without gas jars to be ordered separately.Power supply: 230V 50Hz 1ph 150...
S143 KITUsed for the precise division into two representative portions of materials such as: aggregates, sand, gravel and similar. Painted steel made, it is supplied with two collecting pans.
Used for the determination of specific gravity and water absorption of sands and fine aggregates. Glass jar with aluminium cone and rubber seal.Capacity: 1 kg
ADAPTOR (ring and tamper) for S111 and S112 Extruders: Dia. 150mm
S111 S112Rubber heated pestle for soil mortar.
The plastic limit determines the lowest moisture content of a soil, by wich a sample can be rolled into threads Ø 3 mm without breaking the same neither longitudinally or transversely. The set complete with carrying case comprises:- S178-01 Glass plate 300x250x10 mm- S178-02 Rod caliper &Osla...
Used for splitting materials such as aggregates, sand, gravel and similar into two representative portions. Stainless steel made, they are supplied with two collecting pans. Two models available: Model Slot width Max. size sample mm Slot number Weight Kg Spare collecting pan A062 1-4" - 6.3 mm ...
SMARTIP is a smart automatic apparatus for the determination of the needle penetration value. The instrument automatically reaches the contact point before starting the test and the penetration result is measured thanks to a high performance contactless displacement transducer. MAIN FEATURES: Fully...
Moisture condition value (MCV) and chalk crushing value (CCV) This apparatus is used to measure the minimum comparative effort required to produce near full compaction of a soil, and the rate at which a sample of chalk lumps are crushed.The unit can be used to classify chalk as a fill material with ...
This mould, vertically split on one side, foreseen of clamp attachment to the base plate, plated against corrosion, is utilized for determining the degree of compaction of bituminous pavaments, for quality control purpose.Weight:12 Kg
Used for a smooth and rapid extrusion of soil samples from tubes also of thin walls with minimum disturbance. The unit extrudes samples from Ø 35 up to 150 mm (external diameter 160 mm) with max. stroke of 900 mm.The hydraulic piston is equipped of speed adjuster and can be stopped in any exc...
It provides an alternative method for the compaction of soil samples in the determination of dry density/moisture content relation (called Proctor), unconfined compressive strength of stabilized soils and CBR tests. This hammer is also used for the compaction of asphalt in the percentage r...
CBR loading machine, hand operated, field model The load is applied through a mechanical jack with handwheel. The upper beam can be adjusted in height. The S210KIT machine comprises:S221 Conversion frameS221-01 Mechanical jack 50 kN capacity (provided with its support)S370-10 Load ring 50 kN capacit...
Automatic, programmable PROCTOR / CBR Compactor with microprocessor, “high technology” Designed to compact Proctor and CBR specimens, it ensures an extremely uniform compaction degree, granting reliable and repeatable test results. The microprocessor software allows to select and perform...
TEST GAUGE, to check the condition of the cone point 60° angle.
S165-01KIT S165 KIT S165-02 KIT S166 KITUsed to extrude samples having diameters of 4”, 6”, 100 mm, 150 mm. It can therefore extrude CBR, Marshall and Proctor specimens. The extruder is actuated by a 50 kN hydraulic jack, having ram travel of 190 mm + 170 mm screw.Supplied complete with adaptors.Dimensions: Ø 300x500 m...
TEST CONE 60°angle and 60g weight (liquid limit and shear strength tests).
S165-01KIT S165 KIT S165-02 KIT S166 KITCBR mould complete with collar and perforated base: Dia. 152 mm x 127 mm height
S199Filter screen, stainless steel, 149 mm mesh 0.150 mm (ASTM n° 100)
Hand-operated hydraulic jack, 30 kN capacity. Suitable for the extrusionof 4” diameter specimens from the mould. Dimensions: Ø 200x400 (h) mm.Weight: 20 kg approx.
Tripod (dial gauge support)
Perforated (sweel) plate with adjustable steam.
Annular surcharge weight 2000 g
ASTM, NF, BS
Ø 50 mm fall height 457.2 mm, weight 4.54 kg
Ø 150 mm
600x400x400 mm
Solid base plate for CBR mould.
Perforated base plate for CBR mould.
Spacer disc with “T” handle: Ø 150 mm x 50 mm height
Split surcharge weight 2000 g
No results